Photo 1 sur 4

Scie à couper fine Slugger 14 pouces TCT - Photo 2 sur 4

Scie à couper fine Slugger 14 pouces TCT - Photo 3 sur 4

Scie à couper fine Slugger 14 pouces TCT - Photo 4 sur 4

Vous en avez un à vendre?

Vendez le vôtre

Scie à couper fine Slugger 14 pouces TCT

État :

Neuf – Boîte ouverte

“Customer return with cosmetic blemishes. Corner of cast base is broken”

Prix :

424,95 $US

Environ583,86 $C

Ayez l'esprit tranquille. Renvois acceptés.

Expédition :

60,68 $US (environ 83,37 $C) Expédition standard. En savoir plussur l'expédition

Lieu : Pella, Iowa, États-Unis

Livraison :

Livraison prévue entre le jeu. 13 juin et le sam. 15 juin à 43230

Renvois :

Renvoi sous 30jours. L'acheteur paie les frais de port du renvoi. En savoir plus- pour en savoir plus sur les renvois

Paiements :

Magasinez en toute confiance

Garantie de remboursement eBay

Recevez l'objet commandé ou obtenez un remboursement.

En savoir plusGarantie de remboursement eBay - s'ouvre dans une nouvelle fenêtre ou un nouvel onglet

Informations sur le vendeur

tricktools (4262)
100% d'évaluations positives

Inscrit comme vendeur professionnel

Signaler cet objet - s'ouvre dans une nouvelle fenêtre ou un nouvel onglet

Le vendeur assume l'entière responsabilité de cette annonce.

Numéro de l'objet eBay :185909371922

Caractéristiques de l'objet

État: Neuf – Boîte ouverte

Remarques du vendeur: “Customer return with cosmetic blemishes. Corner of cast base is broken”

Brand: fein

MPN: 72905361120

Description de l'objet du vendeur

Le vendeur assume l'entière responsabilité de cette annonce.

Numéro de l'objet eBay :185909371922

Expédition et manutention

Lieu où se trouve l'objet :

Pella, Iowa, États-Unis

Expédition :

Monde entier

Lieux exclus :

Case postale, Adresses militaires ou navales, Afghanistan, Albanie, Algérie, Andorre, Angola, Anguilla, Antigua-et-Barbuda, Antilles néerlandaises, Argentine, Arménie, Aruba, Azerbaïdjan, Bahamas, Bangladesh, Barbade, Bermudes, Bhoutan, Biélorussie, Bolivie, Bosnie-Herzégovine, Botswana, Brunéi Darussalam, Burkina Faso, Burundi, Bélize, Bénin, Cambodge, Cameroun, Comores, Corée du Sud, Costa Rica, Côte d'Ivoire, Djibouti, Dominique, Fidji, Gabon, République du, Gambie, Ghana, Gibraltar, Grenade, Groenland, Guadeloupe, Guam, Guatemala, Guernesey, Guinée, Guinée équatoriale, Guinée-Bissau, Guyana, Guyane française, Géorgie, Haïti, Honduras, Irak, Islande, Jamaïque, Jersey, Jordanie, Kazakhstan, Kenya, Kirghizistan, Kiribati, Laos, Lesotho, Lettonie, Liban, Libye, Libéria, Liechtenstein, Lituanie, Luxembourg, Macao, Macédoine, Madagascar, Malawi, Maldives, Mali, Maroc, Martinique, Mauritanie, Mayotte, Micronésie, Moldavie, Mongolie, Montserrat, Monténégro, Mozambique, Namibie, Nauru, Nicaragua, Niger, Nigeria, Nioué, Nouvelle-Calédonie, Népal, Oman, Ouganda, Ouzbékistan, Pakistan, Palau, Panama, Papouasie-Nouvelle-Guinée, Paraguay, Polynésie française, Royaume-Uni, Russie, Rwanda, République centrafricaine, République de Croatie, République du Congo, République démocratique du Congo, Réunion, Sahara occidental, Saint-Kitts-et-Nevis, Saint-Marin, Saint-Pierre-et-Miquelon, Saint-Vincent-et-les Grenadines, Sainte-Hélène, Sainte-Lucie, Salvador, Samoa, Samoa américaines, Serbie, Seychelles, Sierra Leone, Somalie, Sri Lanka, Suriname, Svalbard et Jan Mayen, Swaziland, Sénégal, Tadjikistan, Tanzanie, Tchad, Togo, Tonga, Tunisie, Turkménistan, Turquie, Tuvalu, Ukraine, Uruguay, Vanuatu, Venezuela, Vietnam, Wallis-et-Futuna, Yémen, Zambie, Zimbabwe, Égypte, Équateur, Érythrée, État de la Cité du Vatican, Éthiopie, Île Maurice, Îles Caïmans, Îles Cook, Îles Malouines (îles Falkland), Îles Marshall, Îles Salomon, Îles Turks et Caicos, Îles du Cap-Vert

Expédition et manutention	À	Service	Livraison*Voir les remarques sur la livraison
60,68 $US (environ 83,37 $C)	États-Unis	Expédition standard (UPS Ground)	Livraison prévue entre le jeu. 13 juin et le sam. 15 juin à 43230

*Les dates de livraison approximatives – s'ouvre dans une nouvelle fenêtre ou un nouvel onglet tiennent compte du délai de manutention du vendeur, du code postal de l'expéditeur, du code postal du destinataire et de l'heure de l'acceptation et dépendent du service d'expédition sélectionné et de la réception du paiement. Les délais de livraison peuvent varier, particulièrement lors de périodes achalandées.Remarques - Livraison *Les dates de livraison approximatives tiennent compte du délai de manutention du vendeur, du code postal de l'expéditeur, du code postal du destinataire et de l'heure de l'acceptation et dépendent du service d'expédition sélectionné et de la réception du paiement. Les délais de livraison peuvent varier, particulièrement lors de périodes achalandées.

Délai de manutention

Expédition dans les 2 jours ouvrables après réception du paiement.

Taxes

Le vendeur facture une taxe de vente dans

Taxe de vente pour cet objet (185909371922)

Le vendeur facture une taxe de vente pour les États suivants :

État	Taux de la taxe de vente

*La taxe s'applique uniquement au sous-total + frais d'expédition et de manutention pour les objets dans ces États

Modalités de renvoi

Après réception de l'objet, contactez le vendeur dans un délai de	Mode de remboursement
30 jours	Remboursement, Remplacement

Les frais d'expédition du renvoi sont à la charge de l'acheteur.

Détails du paiement

Modes de paiement

Trick-Tools

100% d'évaluations positives

9,9K objets vendus

Visiter la Boutique Contacter

Répond généralement en 24 heures

Évaluations détaillées du vendeur

Moyenne au cours des 12 derniers mois

Qualité de la description

5.0

Justesse des frais d'expédition

4.9

Rapidité de l'expédition

5.0

Communication

4.9

Catégories populaires de cette Boutique

Tout affichercatégories

Used, Demo, or Closeout ItemsTube Bending SoftwareHole Saw KitsTube Rotation GaugesSawing (Band Saws)Grinding & SandingIron Workers & PressesAngle Finders & LevelsMetal Forming and Shaping

Évaluations comme vendeur (5 063)

m***e (133)- Évaluation laissée par l'acheteur.

Dernier mois

Achat vérifié

Fast shipper

Tube Bender Survival Kit with Bend Tech PRO Software (#126092255645)

o***r (2563)- Évaluation laissée par l'acheteur.

Dernier mois

Achat vérifié

Great price and fast shipping on this bullseye pick. Looks to be a nice quality tool. Will work great for my projects.

15 inch Bullseye Pick - 3/8 Construction (#186389415215)

a***3 (512)- Évaluation laissée par l'acheteur.

Dernier mois

Achat vérifié

Fast shipping great quality will buy again

Tube Welding Positioner Kit (#126407386902)

Afficher toutes les évaluations

Évaluations et avis sur le produit

Rédiger un avis

5.0

26 évaluations du produit

26 utilisateurs ont attribué une note de 5 étoiles sur 5
0 utilisateurs ont attribué une note de 4 étoiles sur 5
0 utilisateurs ont attribué une note de 3 étoiles sur 5
0 utilisateurs ont attribué une note de 2 étoiles sur 5
0 utilisateurs ont attribué une note de 1 étoiles sur 5

Would recommend

Good value

Good quality

Avis les plus pertinents

Afficher tous les avis (24)

par nevetsrednut1956
mai 20, 2020
You get what you pay for.
I have been using the Harbor Freight 64.5 band saw for several years and while it works great, it is very slow. I have been reading about and watching videos of the Fein 14 inch Slugger for a while now and so I decided to get one to see what all the hoopla was all about. The package came in two business days. It is well boxed from the factory and arrived undamaged. I had quite a bit of metal that needed to be cut so I brought the saw down stairs....it weighs in at about 65 lbs....not light but not all that heavy to me. I set it up on my workbench and plugged it in. The chain that holds the cutter wheel down while moving it is a bit tight and sticks into the hook by the plastic shield with the warning on it. It was easy to bend and I think I will keep the plastic shield on as it keeps the ... I have been using the Harbor Freight 64.5 band saw for several years and while it works great, it is very slow. I have been reading about and watching videos of the Fein 14 inch Slugger for a while now and so I decided to get one to see what all the hoopla was all about. The package came in two business days. It is well boxed from the factory and arrived undamaged. I had quite a bit of metal that needed to be cut so I brought the saw down stairs....it weighs in at about 65 lbs....not light but not all that heavy to me. I set it up on my workbench and plugged it in. The chain that holds the cutter wheel down while moving it is a bit tight and sticks into the hook by the plastic shield with the warning on it. It was easy to bend and I think I will keep the plastic shield on as it keeps the little chips from hitting my face. I always wear eye protection and I also wear hearing protection although this saw is a lot quieter than some of the other cold cut saws I have used and seen. Using it is easy...a two safety switch system. You have to pull both in towards the handle for the saw to run. Cutting 1.5" x .5 inch square bar was very easy. Did 50 cuts in less than 20 minutes...way way faster than the HF band saw. Cuts were accurate and square. Cut some cold rolled 3/4 round and did that very easily. I took my time cutting, not forcing the cut as the blade really does the work easily. I took a tip from an old timey machinist who uses one of these by spraying the blade with WD40 every 5 cuts or so....just a quick spray while the blade is moving on both sides. He says that the blades will last a lot longer by doing this. It does keep the sparks down although this saw has very few of those...a whole lot less than my Milwaukee abrasive chop saw. And NO DUST!!!!! The chips will land mostly in the tray in the back of the saw although some will bounce around outside the saw and onto the work bench. Wear a heavy duty shirt that will not allow the chips to stick to you. I made the mistake of wearing a wool sweater and I was picking chips out of it...not fun. Make sure you have a shop vac and a wide broom handy. Cleaning up is a lot easier with those. The base is flat and cast...not like some of the other saws that have pressed sheet steel and are not all that flat. Not sure of the longevity of the blade but so far it is holding up very well cutting 1/2 inch thick steel. I hear people getting up to a 1000 cuts....we will see. The blades are around 120 dollars or so which breaks down to about 8 cents a cut depending on if you get 1000 cuts. Even at a slightly higher cost per cut, it is well worth the time saved over other cutting methods. I highly recommend this saw. Built better than many of the others and the blade seems to be very well made. Yeah it is a bit more expensive but as the old timey machinist told me....you get what you pay for.
Achat vérifié : OuiÉtat : NeufVendu par : cpo-outlets
par lr_tig_magic
févr. 22, 2021
Best Quality Saw!
I bought the 14” Fein Slugger Dry Cut Metal Saw over 6 months ago. I bought this saw for my own shop at home, but I use an Evolution 14” saw at work. The Evolution is still 1000X better than any abrasive saw, but the Slugger blows it way out of the water! There is really no comparison between them. The Evolution’s base is about as flat as a pretzel, it’s stamped, thin sheet steel with waves, peaks, low-points, and a super rough surface. You can’t even put a square up the front edge to true the fence angle up to the blade. The angle gauge is completely useless and inaccurate, so if you need any amount of precision, you’ll have to dial it in every time through trial and error. Basically it’s a guessing game with the Evo. Beyond that, the work holding mechanism is not very rigid for several ... I bought the 14” Fein Slugger Dry Cut Metal Saw over 6 months ago. I bought this saw for my own shop at home, but I use an Evolution 14” saw at work. The Evolution is still 1000X better than any abrasive saw, but the Slugger blows it way out of the water! There is really no comparison between them. The Evolution’s base is about as flat as a pretzel, it’s stamped, thin sheet steel with waves, peaks, low-points, and a super rough surface. You can’t even put a square up the front edge to true the fence angle up to the blade. The angle gauge is completely useless and inaccurate, so if you need any amount of precision, you’ll have to dial it in every time through trial and error. Basically it’s a guessing game with the Evo. Beyond that, the work holding mechanism is not very rigid for several reasons. The first, most obvious one is just that the entire base is a flimsy, pretzeled up piece of sheet steel. Second, the vibration of the saw and workpiece aren’t too bad, but there’s way more vibration and blade deflection & walking than the Slugger. The third only applies when trying to make a miter cut, as the movable jaw can’t provide sufficient surface area or the proper balance of clamping forces to support the workpiece at any angle other than 90°, so the workpiece moves, causing the angle to come out wrong every time. The Evolution blades cut much slower than the Slugger blades, they vibrate, walk, deflect, and don’t maintain smooth cutting action like the Slugger blades do. The Slugger is a beast, weighing over 60lbs. The base is very flat and has a super smooth surface finish, as do the vise jaws. The base is somewhere around 1 inch thick and is a solid casting, most likely machined from MIC-6 or some similar cast tool & jig plate alloy. The cutting action is very quiet, extremely fast and smooth. You can’t feel the teeth of the blade contacting the work, it’s just a swift glide through the material every time. It’s very consistent, precise, and leaves a much better finish without burrs relative to the Evo or any other metal cutting method/machine except for maybe a good milling machine! The Slugger is just a beautiful machine in every way. It’s solid, it was very obviously made with great precision and attention to quality and detail. If you’re someone who appreciates, and values precision, quality, accuracy, repeatability, efficiency, and craftsmanship, then this is THE machine for you. It is absolutely worth every penny to have such a well built saw that you can rely on to produce high quality results every time and will hold up to industrial use for years to come. For me, it’s also really nice that I can make cuts without generating a lot of noise, and without any dust or sparks, or surface contaminants. If you need a great saw, you will never regret investing in the Slugger.
État : NeufVendu par : cpo-outlets
par rusty_bolts
nov. 13, 2019
Nice clean quiet cuts. Heavy duty, well made, except for the little clear plastic shield.
Works great. Cuts smooth and straight. Much quieter than a usual abrasive type chop saw. The shavings that come off are hot and sharp, so watch where you put your hands when you're done. The only thing I don't like is the little clear plastic shield which seems like an afterthought, and isn't really necessary if you're wearing eye or face protection, so I might just take it off. The saw is pretty heavy, so it's not something I would want to carry around very far.Works great. Cuts smooth and straight. Much quieter than a usual abrasive type chop saw. The shavings that come off are hot and sharp, so watch where you put your hands when you're done. The only thing I don't like is the little clear plastic shield which seems like an afterthought, and isn't really necessary if you're wearing eye or face protection, so I might just take it off. The saw is pretty heavy, so it's not something I would want to carry around very far.
Achat vérifié : OuiÉtat : NeufVendu par : spreetail
par dan_merrick
avr. 10, 2019
EXCELLENT metal cutting tool.
This cutter cuts so well it startled me. My first cut was a 2" 10 gauge square steel tube. It took less than 10 seconds to cut it. The cut was beautiful and I could touch it immediately. My older but, brand new high RPM cutter (with a metal cutting carbide blade) would have taken 100 seconds, caused the metal to glow red hot and distorted the cut. Considering you get a new blade on the device the price is competetive.This cutter cuts so well it startled me. My first cut was a 2" 10 gauge square steel tube. It took less than 10 seconds to cut it. The cut was beautiful and I could touch it immediately. My older but, brand new high RPM cutter (with a metal cutting carbide blade) would have taken 100 seconds, caused the metal to glow red hot and distorted the cut. Considering you get a new blade on the device the price is competetive.
Achat vérifié : OuiÉtat : NeufVendu par : cpo-outlets
par adtrailers
oct. 01, 2019
Better than I expected!
I build metal fab projects and burned up a 20yr old Dewalt abrasive chop saw a couple weeks ago. I didn't want another abrasive saw, so I started doing research. This Fein Slugger is very impressive and the cuts are smooth and exact. The saw also saves so much time because the metal has smooth edges that are ready to weld. I'm very happy so far.
Achat vérifié : OuiÉtat : NeufVendu par : factory_authorized_outlet

Photo 1 sur 4

Scie à couper fine Slugger 14 pouces TCT

Magasinez en toute confiance

Informations sur le vendeur

Caractéristiques de l'objet

Description de l'objet du vendeur

Expédition et manutention

Modalités de renvoi

Détails du paiement

Trick-Tools

Évaluations détaillées du vendeur

Moyenne au cours des 12 derniers mois

Catégories populaires de cette Boutique

Évaluations comme vendeur (5 063)

Évaluations et avis sur le produit

Avis les plus pertinents

You get what you pay for.

Best Quality Saw!

Nice clean quiet cuts. Heavy duty, well made, except for the little clear plastic shield.

EXCELLENT metal cutting tool.

Better than I expected!