jackbechtel sur eBay

À propos

Lieu : États-UnisMembre depuis : 19 juin 2001

Évaluations

12 derniers mois

Positives11- évaluations positives au cours des 12 derniers mois

Neutres0- évaluations neutres au cours des 12 derniers mois

Négative0- évaluations négatives au cours des 12 derniers mois

Toutes les évaluations (497)

gold-coins (36726)- Évaluation laissée par l'acheteur.
Il y a plus d'un an
Achat vérifié
Good buyer, prompt payment, valued customer, highly recommended.
retrocove (3423)- Évaluation laissée par l'acheteur.
Il y a plus d'un an
Achat vérifié
Good buyer, prompt payment, valued customer, highly recommended.
trainz (684667)- Évaluation laissée par l'acheteur.
Il y a plus d'un an
Achat vérifié
Super eBayer! Absolute Perfection! Many Thanks From Trainz!!!
kastarusa1 (255879)- Évaluation laissée par l'acheteur.
Six derniers mois
Achat vérifié
Thank you very much for your order!
kwdjliqwil_0 (1433)- Évaluation laissée par l'acheteur.
Six derniers mois
Achat vérifié
Hope to deal with you again. Thank you.
2006cucci (530)- Évaluation laissée par l'acheteur.
Il y a plus d'un an
Achat vérifié
Great Ebayer! A+++

Afficher toutes les évaluations

Avis (4)

10PCS Pre-Soldered 0402 1005 Warm White Light Pre Wired 20CM SMD LED Diodes

13 nov. 2020

Excellent LED's for HO model train headlights

Most excellent LED's for HO model train headlights, nice and bright with perfect warm white color. They fit comfortably epoxied into a 0.036" hole drilled into either oem plastic headlight lenses or a short 0.060" fiber. You can also use them directly in place of grain-of-wheat bulbs with no lenses at all as long as the LED's are not touching metal. Wires are thin, flexible, tough and easy to fit inside loco's. You can wire 2 of them in series for dual headlights and use a single 1K ohm resistor (i.e., 2 LEDS + a 1K in front and 2 LED's and a 1K for the rear). I put the lenses or bare led's loose in the headlight hole, tack them in place with adhesive putty over their wires and then anchor the wires semi-permanently to the inside of the shell using a drop of epoxy. Voila, easy, non-destructive replacement in case of problems, although I haven't had a bad one yet. Keep making more, please! If you can make them fit, they should do fine in other gauges and types of models as well.

Märklin 7152 Traction Tires, New Pack of Ten, Superfast Low cost USA Shipping!

08 févr. 2019

Marklin Traction Tires are bar none, the best !

I have about a hundred HO locos with traction tires running on 2-1/2% grades. I own a mini-lathe with a setup dedicated to cutting the grooves for tires. I've tried various brands of traction tires and found these to be the most uniform in thickness and width and best in quality of material and durability. They're easy to install and tolerant of the stretching and abrasion that occurs during installation. They provide consistent traction, are never out-of-round or bumpy and none has ever fallen off a wheel. Best of all, my locos haul heavy trains like mad. - L Arellano

6pc 7" Diamond Flat File Set 9mm x 180mm x 70mm 40-600 Grit Ceramics Tile Glass

28 oct. 2021

Excellent results on chain saw bar

Product worked exactly as expected to square up the groove edges on my Stihl chainsaw bar. I attached the file to a wood block with 2 tiny blobs of fun-tak, laid the bar on a 1/16" piece of G20 and slid the block with file across the bar edges. I rough filed the sharp ridges down with a coarse file and then finished it with a fine file. Had to bend the file handles about 10-15 degrees and shave them a little to get clearance and better contact, not a problem. Results were much more accurate and smoother than free-hand grinding on a carborundum wheel. The files cut the hard bar faster and easier than a steel file, while barely taking any wear.

Afficher tous les avis